Witch Hat Mahjong Solitaire

0:00

Play Levels — Campaign Browse Layouts This board More Home How to Play Rules

About the Witch Hat Layout

The Witch Hat layout is a tall, dramatic silhouette: a steep pointed cone of tiles rising from a broad, flat circular brim, with the very tip kinked slightly to one side as if it has been worn a hundred Halloweens. The brim spreads wide and shallow at the bottom, just one or two courses tall, while the cone above narrows row by row to a single bent point. The contrast between the sprawling brim and the slender peak gives the board real vertical character.

Rated three out of five, the Witch Hat is a moderate challenge with an unusual rhythm. The wide brim is easy and open, almost a warm-up, but the cone is where the game tightens. As the hat narrows, fewer tiles sit on each row and they stack deeper toward the center spine, so the climb from brim to tip gets progressively trickier. It feels playful and a little spooky, with a satisfying sense of working your way up to that crooked point.

Difficulty: Hard (3/5) | Tiles: 140

How to Clear the Witch Hat Layout

Begin with the brim. The flat circular base is wide and mostly single-layer, so its outer edges are all free. Sweeping the brim clean first removes the largest bank of tiles fast and gives you momentum before the cone demands more care.

Climb the cone in alternating sweeps. Each row of the cone has exposed left and right ends, so pick off the outermost tiles on one side, then the other, letting the cone narrow evenly. If you gut one side of the cone while leaving the other stacked, you risk burying tiles along the central spine.

The crux is the join where the cone meets the brim. That seam carries the deepest overlap on the whole board because the wide base and the rising cone both pile up there. Do not fully strip the brim away before opening the lowest cone rows, or you may trap the tiles sitting on that shoulder. Interleave a few brim matches with the first cone rows to keep the shoulder breathing.

The endgame lives at the bent tip. The kinked point is a small cluster of tiles right at the top, and because the bend offsets them they can hide one another. Aim to arrive there with the cone already thinned so the final few tiles have open sides. If the tip or the shoulder locks up, Shuffle re-deals the leftover tiles solvably and usually springs the point loose.

The Story Behind the Witch Hat Layout

The pointed witch hat is a surprisingly modern costume invention, but its conical crown echoes the tall hats worn across medieval Europe, and folklore tied the steeple shape to figures standing apart from the crowd. Victorian illustrators fixed the bent-tip, wide-brim witch in the popular imagination, and it has been the instant shorthand for a witch ever since.

As a Mahjong board the hat is a gift of geometry. The brim gives you a broad, forgiving foundation, the cone provides a natural difficulty ramp as it tapers, and that little crook at the tip adds a personality-filled puzzle at the summit. Few shapes turn so cleanly into an easy-start, tense-finish climb.

Frequently Asked Questions

Where are the easiest tiles on the Witch Hat?

The brim. The wide flat circle at the bottom is only a course or two deep, so its outer rim tiles all have free edges. Clearing the brim first is the natural, low-risk way to open the board.

Why does the cone get harder as I go up?

Each row of the cone holds fewer tiles but they cluster and stack toward the central spine, so near the top the same height of stacking is packed into a narrow point. Fewer free edges are available the higher you climb, which is what makes the upper cone the test.

What about the bent tip at the very top?

The kink offsets the topmost tiles so they can cover one another more than a straight point would. Try to reach the tip with the rest of the cone already cleared, leaving those few tiles with open sides. If they stall, Shuffle will re-deal them into a solvable position.

Do I have to clear the brim completely before the cone?

No, and you should not. The brim-to-cone seam is the deepest part of the board, so blend a few of the lowest cone matches with your last brim tiles to avoid trapping the shoulder where the two sections meet.

Browse all layouts or play the classic Turtle board.